ASTM F2248 PDF

¼” screws at four jamb corners – screws bending corners screws bending. – tearing in frame wall at connections pushing limits of ASTM F □ Minimal. ASTM F Standard Practice for Specifying an Equivalent 3-Second Duration Design Loading for Blast Resistant Glazing Fabricated with. Mullion/Frame Design – Allowable Stress Design. ▫ Design Load = Equivalent 3 second design load ASTM F ▫ Info Required –. ▫ 1) Level of Protection.

Author: Zugami Kasida
Country: Uzbekistan
Language: English (Spanish)
Genre: Spiritual
Published (Last): 23 February 2013
Pages: 28
PDF File Size: 3.99 Mb
ePub File Size: 18.51 Mb
ISBN: 837-2-44720-176-3
Downloads: 99909
Price: Free* [*Free Regsitration Required]
Uploader: Shaktisho

ASTM F – Wikipedia

From Wikipedia, the free encyclopedia. The width of glazing tape shall be at least equal to two times but not more than four times the thickness designation of the glass to which it wstm. The system shall be designed to ensure that the glazing fails prior to the framing system that supports the glazing and its attachment to the structural framing system.

The standard explain different methods to check the thickness and type of blast resistant glazing fabricated with laminated glass to glaze a fenestration. Blast testing has shown that use of fully tempered glass plies, when fractured during a blast event, have poorer post blast performance than annealled or heat strengthened glass plies.

The standard explain different methods to check the thickness and type of blast resistant glazing fabricated with laminated glass to glaze a fenestration The main keywords to present this standard are air blast pressure, blast resistant glazing, explosion, insulating glass, and laminated glass.

Glass plies zstm to construct laminated glass are recommended to be either annealed or heat strengthened glass.

Glass plies used to construct laminated glass are recommended to be either annealed or heat strengthened glass. The width of silicone or glazing tape is referred to as bite and is shown and discussed in Guide C The width of glazing tape shall be at least equal to two times but not more than four times the thickness designation of the glass to which it adheres.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. As a minimum, insulating glass shall use laminated glass for atm inboard protected side lite. Use of the annealed or heat strengthened glass plies will also reduce the amount of load transferred into the structure. By using this site, you agree to the Terms of Use and Privacy Policy.

  FARMACOCINETICA METAMIZOL PDF

Work Item s – proposed revisions of this standard. Blast testing has shown that use of fully tempered glass plies, when fractured during a blast xstm, have poorer post blast performance than annealled or heat strengthened glass plies.

Work Item g2248 – proposed revisions of this standard. Laminated glass fabricated with fully tempered glass plies has a tendency to leave the supporting glazing system frame after fracture whereas laminated glass fabricated with annealed or heat strengthened glass plies will remain in the frame and absorb remaining load through tensile membrane behavior. Link to Active This link will always route to the current Active version of the standard. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Link to Active This link will always route to the current Active version of the standard.

The fasteners that attach the framing system that supports the glazing to the structural framing system shall be designed to resist a uniform load acting on the blast resistant glazing that has a magnitude of at least:. Values given in parentheses are for information only.

As a minimum, insulating glass shall use laminated glass for the inboard protected side lite. Views Read Edit View history.

Values given in parentheses are for information only. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Use of the annealed or heat strengthened glass plies will also reduce the amount of load transferred into the structure. This page was last edited on 28 Marchat This standard was published by ASTM F14 which is a committee specializes about on systems products and services. Active view current version of standard.

  JOYCE APPLEBY THE RELENTLESS REVOLUTION PDF

ASTM F 2248

The fasteners that attach the framing system that supports the glazing to the structural framing system shall be designed to resist a uniform load acting on the blast resistant glazing that has a magnitude of at least: It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM F is a standard practice for specifying an equivalent 3-Second Duration design loading for blast resistant glazing fabricated with laminated glass. The system shall be designed to ensure that the glazing fails prior to the framing system that supports the glazing and its attachment to the structural framing system.

Historical Version s – view previous versions of standard.

ASTM F2248 – 12

The fasteners that attach the framing system that supports the glazing to the structural framing system shall be designed to resist a uniform load acting on the blast resistant glazing that has a magnitude g2248 at least:. ASTM International which was funded inis an international standards developing organization that develops and publishes standards for a wide range of materials, products, systems, and services. The main keywords to present this standard are air blast pressure, blast resistant glazing, explosion, insulating glass, and laminated glass.

The width of silicone or glazing tape is referred to as bite and is shown and discussed in Guide C Laminated f22448 fabricated with fully tempered glass plies has a tendency to leave the supporting glazing system frame after fracture whereas laminated glass fabricated with annealed or heat strengthened glass plies will remain in the frame and absorb remaining load through tensile membrane behavior.

The fasteners that attach the framing system that supports the glazing to the structural framing system shall be designed to resist a uniform load acting on the blast resistant glazing that has a magnitude of at least: Retrieved from ” https: